Sealing Products

Material:
Sleeve: Stainless steel 1.4305
Ball: Stainless steel 1.4301










Part Number

d₁

Ø

I

I2 ~

Ref.

d

+0.10

d₃max.

I₃ min.

x

±0.2

MB 600-030 3.0 3.6 4.6 3.0 2.2 3.4 0.4
MB 600-040 4.0 4.0 5.1 4.0 3.3 3.8 0.2
MB 600-050 5.0 5.5 7.1 5.0 4.3 5.3 0.4
MB 600-060 6.0 6.5 8.6 6.0 5.3 6.3 0.4
MB 600-070 7.0 7.5 10.1 7.0 6.4 7.3 0.4
MB 600-080 8.0 8.5 11.6 8.0 7.4 8.3 0.3
MB 600-090 9.0 10.0 13.5 9.0 8.4 9.8 0.4
MB 600-100 10.0 11.0 15.1 10.0 9.4 10.8 0.4
MB 600-120 12.0 13.0 17.8 12.0 10.6 12.8 0.4
MB 600-140 14.0 15.0 20.5 14.0 12.7 14.5 0.4

Dimensions in mm

 

Pressure Performance

 

Series
MB 600
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AlMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 3 - 10     1.400 bar / 20.300 psi

   450 bar / 6.500 psi

    1.200 bar / 17.400 psi

   380 bar / 5.500 psi

 
Ø 12 - 14    

1.000 bar / 14.500 psi

   350 bar / 5.100 psi

   

900 bar / 13.000 psi

   280 bar / 4.100 psi

 
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Stainless steel 1.4305
Ball: Stainless steel 1.4301 (MB 600-093 - 1.4034)


Part Number

d1  

Ø

l1

l2 ~

Ref.

d2

d3 max

l3 min.

x

+0

-0.012

MB 600-093A 0.093 0.100 0.120 0.0937 0.062 0.095 0.012
MB 600-125A 0.125 0.138 0.170 0.1250 0.093 0.125 0.012
MB 600-156A 0.156 0.150 0.195 0.1562 0.125 0.130 0.012
MB 600-187A 0.187 0.193 0.260 0.1875 0.156 0.152 0.012
MB 600-218A 0.218 0.225 0.300 0.2187 0.187 0.187 0.012
MB 600-250A 0.250 0.260 0.350 0.2500 0.218 0.212 0.012
MB 600-281A 0.281 0.285 0.380 0.2812 0.250 0.250 0.012

Dimensions in inches

 

Pressure Performance

Series
MB 600
inch
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 0.093 - 0.281     1.400 bar / 20.300 psi

  450 bar / 6.500 psi

    1.200 bar / 17.400 psi

  380 bar / 5.500 psi

 
Proof Pressure Test

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Stainless steel 1.4305, plain finish
Ball: Bearing steel, heat treated


Part Number

d1 l1 l2 ~
Ref.

d2

+0,1

0

d3 max l3 min.

x

± -0.2

 MB 700-030 3.0 3.6 4.6 3.0 2.2 3.4 0.4
 MB 700-040 4.0 4.0 5.1 4.0 3.3 3.8 0.2
 MB 700-050 5.0 5.5 7.1 5.0 4.3 5.3 0.4
 MB 700-060 6.0 6.5 8.6 6.0 5.3 6.3 0.4
 MB 700-070 7.0 7.5 10.1 7.0 6.4 7.3 0.4
 MB 700-080 8.0 8.5 11.6 8.0 7.4 8.3 0.3
 MB 700-090 9.0 10.0 13.5 9.0 8.4 9.8 0.4
 MB 700-100 10.0 11.0 15.1 10.0 9.4 10.8 0.4
 MB 700-120 12.0 13.0 17.8 12.0 10.6 12.8 0.4
 MB 700-140 14.0 15.0 20.4 14.0 12.7 14.5 0.4
 MB 700-160 16.0 17.0 23.4 16.0 14.7 16.5 0.6
 MB 700-180 18.0 19.0 26.3 18.0 16.7 18.5 0.6
 MB 700-200 20.0 22.0 30.0 20.0 18.7 21.5 0.8
 MB 700-220 22.0 25.0 34.0 22.0 20.7 24.5 0.8

Dimensions in mm

 

Pressure Performance

 

 

Series
MB 700
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 3 - 10     1.400 bar / 20.300 psi

   450 bar / 6.500 psi

    1.200 bar / 17.400 psi

   380 bar / 5.500 psi

 
Ø 12 - 22    

1.150 bar / 16.700 psi

350 bar / 5.100 psi

   

900 bar / 13.000 psi

280 bar / 4.100 psi

 
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Case hardening steel zinc plated, thick coat passivated, CR (VI)-free
Ball: Bearing steel, heat treated


Part Number

d1

l1

l2 ~
Ref.

d2

+0,10

d3 max

l3 min.

x
± 0.2
 MB 850-030 3.0 3.6 4.6 3.0 2.2 3.4 0.4
 MB 850-040 4.0 4.0 5.2 4.0 3.3 3.8 0.2
 MB 850-050 5.0 5.5 7.1 5.0 4.3 5.3 0.4
 MB 850-060 6.0 6.5 8.6 6.0 5.3 6.3 0.4
 MB 850-070 7.0 7.5 10.1 7.0 6.4 7.3 0.4
 MB 850-080 8.0 8.5 11.6 8.0 7.4 8.3 0.3
 MB 850-090 9.0 10.0 13.6 9.0 8.4 9.8 0.4
 MB 850-100 10.0 11.0 15.1 10.0 9.4 10.8 0.4
 MB 850-120 12.0 13.0 17.9 12.0 10.6 12.8 0.4
 MB 850-140 14.0 15.0 20.6 14.0 12.7 14.5 0.4
 MB 850-160 16.0 17.0 23.4 16.0 14.7 16.5 0.6
 MB 850-180 18.0 19.0 26.4 18.0 16.7 18.5 0.6
 MB 850-200 20.0 22.0 30.1 20.0 18.7 21.5 0.8
 MB 850-220 22.0 25.0 34.0 22.0 20.7 24.5 0.8

Dimensions in mm

 

Pressure Performance

 

 

Series
MB 850
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 3 – 10     1.100 bar / 16.000 psi

   350 bar / 5.100 psi

    1.000 bar / 14.500 psi

   320 bar / 4.600 psi

 
Ø 12 - 22     900 bar / 13.000 psi
   280 bar / 4.100 psi
    800 bar / 11.600 psi

250 bar / 3.600 psi

 
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6, Anodized Green, MIL-A-8625: Typ II, Class 2
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max. l3 min.

x

± 0.10

s
CV 143-030 3.0 3.18 4.1 3.0 2.3 2.9 0.2 1.0
CV 143-040 4.0 4.00 5.2 4.0 3.3 3.8 0.2 1.4
CV 143-050 5.0 5.50 7.0 5.0 4.3 5.3 0.2 1.9
CV 143-060 6.0 6.50 8.6 6.0 5.3 6.3 0.2 2.3
CV 143-070 7.0 7.50 10.1 7.0 6.2 7.3 0.2 2.8
CV 143-080 8.0 8.50 11.7 8.0 7.2 8.3 0.2 3.4
CV 143-090 9.0 10.0 13.7 9.0 8.2 9.8 0.2 3.7
CV 143-100 10.0 11.0 15.2 10.0 9.2 10.8 0.2 4.2
CV 143-120 12.0 13.0 18.0 12.0 11.0 12.8 0.2 5.1
CV 143-140 14.0 15.0 20.8 14.0 13.0 14.5 0.2 5.9
CV 143-160 16.0 17.0 23.7 16.0 14.7 16.5 0.2 6.4
CV 143-180 18.0 19.0 26.3 18.0 16.7 18.5 0.2 7.2
CV 143-200 20.0 22.0 30.5 20.0 18.7 21.5 0.2 8.4
CV 143-220 22.0 25.0 34.2 22.0 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 143
mm
Base material of the Installation
  AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10   170 bar / 2500 psi        
Ø 12 - 22            
Hole Tolerance     0 / + 0.1 mm      
Hole Roughness  Anchorage   Rz 10 - 30µm      

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Operation

AttachmentSize
Montagerichtlinien Serie CV DE.pdf173.32 KB

Technical Information

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6, allodined chromate conversion, MIL-C 5541
Ball: Stainless steel. AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max l3 min.

x

± 0.10

   s
CV 163-030 3.0 3.18 4.1 3.00 2.3 2.9 0.2 1.0
CV 163-040 4.0 4.00 5.2 4.00 3.3 3.8 0.2 1.4
CV163-050 5.0 5.50 7.0 5.00 4.3 5.3 0.2 1.9
CV 163-060 6.0 6.50 8.6 6.00 5.3 6.3 0.2 2.3
CV 163-070 7.0 7.50 10.1 7.00 6.2 7.3 0.2 2.8
CV 163-080 8.0 8.50 11.7 8.00 7.2 8.3 0.2 3.4
CV 163-090 9.0 10.00 13.7 9.00 8.2 9.8 0.2 3.7
CV 163-100 10.0 11.00 15.2 10.00 9.2 10.8 0.2 4.2
CV 163-120 12.0 13.00 18.0 12.00 11.0 12.8 0.2 5.1
CV 163-140 14.0 15.00 20.8 14.00 13.0 14.5 0.2 5.9
CV 163-160 16.0 17.00 23.7 16.00 14.7 16.5 0.2 6.4
CV 163-180 18.0 19.00 26.3 18.00 16.7 18.5 0.2 7.2
CV 163-200 20.0 22.00 30.5 20.00 18.7 21.5 0.2 8.4
CV 163-220 22.0 25.00 34.2 22.00 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 163
mm
Base material of the Installation
AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10   170 bar / 2500 psi      
Ø 12 - 22          
Hole Tolerance     0 / + 0.1 mm    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max l3 min.

x

± 0.10

 s
CV 173-030 3.0 3.18 4.1 3.00 2.3 2.9 0.2 1.0
CV 173-040 4.0 4.00 5.2 4.00 3.3 3.8 0.2 1.4
CV173-050 5.0 5.50 7.0 5.00 4.3 5.3 0.2 1.9
CV 173-060 6.0 6.50 8.6 6.00 5.3 6.3 0.2 2.3
CV 173-070 7.0 7.50 10.1 7.00 6.2 7.3 0.2 2.8
CV 173-080 8.0 8.50 11.7 8.00 7.2 8.3 0.2 3.4
CV 173-090 9.0 10.00 13.7 9.00 8.2 9.8 0.2 3.7
CV 173-100 10.0 11.00 15.2 10.00 9.2 10.8 0.2 4.2
CV 173-120 12.0 13.00 18.0 12.00 11.0 12.8 0.2 5.1
CV 173-140 14.0 15.00 20.8 14.00 13.0 14.5 0.2 5.9
CV 173-160 16.0 17.00 23.7 16.00 14.7 16.5 0.2 6.4
CV 173-180 18.0 19.00 26.3 18.00 16.7 18.5 0.2 7.2
CV 173-200 20.0 22.00 30.5 20.00 18.7 21.5 0.2 8.4
CV 173-220 22.0 25.00 34.2 22.00 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 173
mm
Base material of the Installation
AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10   170 bar / 2500 psi      
Ø 12 - 22          
Hole Tolerance     0 / + 0.1 mm    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (316) ASTM A580, passivate, QQ-P-35C
Ball: Stainless steel, AISI 316, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max l3 min.

x

± 0.10

 s
CV 588-030 3.0 3.18 4.1 3.00 2.3 2.9 0.2 1.0
CV 588-040 4.0 4.00 5.2 4.00 3.3 3.8 0.2 1.4
CV 588-050 5.0 5.50 7.0 5.00 4.3 5.3 0.2 1.9
CV 588-060 6.0 6.50 8.6 6.00 5.3 6.3 0.2 2.3
CV 588-070 7.0 7.50 10.1 7.00 6.2 7.3 0.2 2.8
CV 588-080 8.0 8.50 11.7 8.00 7.2 8.3 0.2 3.4
CV 588-090 9.0 10.00 13.7 9.00 8.2 9.8 0.2 3.7
CV 588-100 10.0 11.00 15.2 10.00 9.2 10.8 0.2 4.2
CV  588-120 12.0 13.00 18.0 12.00 11.0 12.8 0.2 5.1
CV 588-140 14.0 15.00 20.8 14.00 13.0 14.5 0.2 5.9
CV 588-160 16.0 17.00 23.7 16.00 14.7 16.5 0.2 6.4
CV 588-180 18.0 19.00 26.3 18.00 16.7 18.5 0.2 7.2
CV 588-200 20.0 22.00 30.5 20.00 18.7 21.5 0.2 8.4
CV 588-220 22.0 25.00 34.2 22.00 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 588
mm
Base material of the Installation
AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10     450 bar / 6500 psi    
Ø 12 - 22          
Hole Tolerance     0 / + 0.1 mm    
Hole Roughness  Anchorage       Rz 10 -30µm

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-Q 225/6, anodized green, MIL-A-8625: Type II, Class 2
Ball: Stainless steel, AISI 302/304, wax film lubrication (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 143-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 143-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV143-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 143-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 143-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 143-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 143-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 143-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 143-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 143-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 143-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 143-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 143-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 143-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 143-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV 143-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 143
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375   170 bar / 2500 psi      
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A-225/6, allodined chromate, MIL-C 5541
Ball: Stainless steel, AISI 302/304, wax film lubrication (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.0040

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 163-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 163-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV163-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 163-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 163-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 163-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 163-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 163-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 163-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 163-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 163-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 163-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 163-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 163-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 163-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV 163-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 163
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375   170 bar / 2500 psi      
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (303), ASTM A582
Ball: Bearing steel, heat treated, black oxide & wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 531-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 531-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV 531-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 531-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 531-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 531-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 531-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 531-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 531-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 531-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 531-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 531-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 531-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 531-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 531-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV 531-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 531
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375     450 bar / 6500 psi    
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (316) ASTM A580, passivate, QQ-P-35C
Ball: Stainless steel, AISI 316, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 588-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 588-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV 588-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 588-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 588-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 588-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 588-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 588-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 588-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 588-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 588-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 588-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 588-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 588-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 588-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV  588-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 588
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375     450 bar / 6500 psi    
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Case hardening steel ASTM A108, zinc chromate ASTM B633: Type III, trivalent
Ball: Bearing steel, heat treated, black oxide & wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 851-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 851-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV 851-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 851-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 851-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 851-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 851-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 851-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 851-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 851-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 851-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 851-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 851-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 851-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 851-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV  851-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 851
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375     450 bar / 6500 psi    
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6, anodized green, MIL-A-8625: Type II, Class 2
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 143-125S 0.125 0.125 .16 0.1250 0.100 0.113 0.007 0.042
CV 143-156S 0.156 0.125 .17 0.1562 0.130 0.113 0.000 0.040
CV143-187S 0.187 0.187 .24 0.1875 0.160 0.170 0.010 0.066
CV 143-218S 0.218 0.187 .25 0.2187 0.190 0.170 0.000 0.063
CV 143-250S 0.250 0.225 .30 0.2500 0.220 0.196 0.000 0.083
CV 143-281S 0.281 0.255 .35 0.2812 0.250 0.233 0.000 0.091
CV 143-312S 0.312 0.280 .39 0.3125 0.281 0.255 0.000 0.107
CV 143-343S 0.343 0.307 .43 0.3437 0.312 0.275 0.000 0.118
CV 143-406S 0.406 0.365 .52 0.4062 0.375 0.308 0.010 0.143

Dimensions in inches

Pressure Performance

Series
CV 143 Short
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.125 - 0.406   120 bar / 1750 psi      
Hole Tolerance     Ø 0.125:0 / +0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A-225/6, allodined chromate conversion, MIL-C 5541
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 163-125S 0.125 0.125 .16 0.1250 0.100 0.113 0.007 0.042
CV 163-156S 0.156 0.125 .17 0.1562 0.130 0.113 0.000 0.040
CV163-187S 0.187 0.187 .24 0.1875 0.160 0.170 0.010 0.066
CV 163-218S 0.218 0.187 .25 0.2187 0.190 0.170 0.000 0.063
CV 163-250S 0.250 0.225 .30 0.2500 0.220 0.196 0.000 0.083
CV 163-281S 0.281 0.255 .35 0.2812 0.250 0.233 0.000 0.091
CV 163-312S 0.312 0.280 .39 0.3125 0.281 0.255 0.000 0.107
CV 163-343S 0.343 0.307 .43 0.3437 0.312 0.275 0.000 0.118
CV 163-406S 0.406 0.365 .52 0.4062 0.375 0.308 0.010 0.143

Dimensions in inches

Pressure Performance

Series
CV 163 Short
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.125 - 0.406   120 bar / 1750 psi      
Hole Tolerance     Ø 0.125:0 / +0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (316) ASTM A580, passivate, QQ-P-35C
Ball: Stainless steel, AISI 316, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 588-125S 0.125 0.125 .16 0.1250 0.100 0.113 0.007 0.042
CV 588-156S 0.156 0.125 .17 0.1562 0.130 0.113 0.000 0.040
CV588-187S 0.187 0.187 .24 0.1875 0.160 0.170 0.010 0.066
CV 588-218S 0.218 0.187 .25 0.2187 0.190 0.170 0.000 0.063
CV 588-250S 0.250 0.225 .30 0.2500 0.220 0.196 0.000 0.083
CV 588-281S 0.281 0.255 .35 0.2812 0.250 0.233 0.000 0.091
CV 588-312S 0.312 0.280 .39 0.3125 0.281 0.255 0.000 0.107
CV  588-343S 0.343 0.307 .43 0.3437 0.312 0.275 0.000 0.118
CV 588-406S 0.406 0.365 .52 0.4062 0.375 0.308 0.010 0.143

Dimensions in inches

Pressure Performance

Series
CV 588 Short
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.125 - 0.406   250 bar / 3600 psi      
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage in Base Material       Rz 10 - 30µm

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Case hardening steel, gun metal-finish
Mandrel: Heat treatable steel, special oil film lubrification


Part Number

d1

l1 d2 l2 I3 max. I4 max.

d3
+ 0.120

SK550-040 4.0 4.5 2.50 39 9.0 6.5 4.0
SK550-050 5.0 5.5 3.00 41 10.0 7.5 5.0
SK550-060 6.0 6.5 3.40 43 12.0 8.0 6.0
SK550-070 7.0 7.5 4.10 38 14.0 9.0 7.0
SK550-080 8.0 8.5 4.20 40 15.0 10.5 8.0
SK550-090 9.0 9.5 4.50 43 17.0 11.0 9.0
SK550-100 10.0 10.5 4.75 45 19.0 12.5 10.0
SK550-120 12.0 12.5 5.7 50 24.0 16.50 12.0

Dimensions in mm

Pressure Performance

Series
SK
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 10     1.600 bar / 23.200 psi

   500 bar / 7.200 psi

    1.400 bar / 20.300 psi

   450 bar / 6.500 psi

 

 
Ø 12     1.600 bar / 23.200 psi

   400 bar / 5.800 psi

       
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation Instrution SK.pdf454.92 KB

Technical Information

Material:
Sleeve: Case hardening steel, gun metal-finish
Mandrel: Heat treatable steel, special oil film lubrification

One piece construction, ideal for automated high production requirements

Special Type: with mandrel 30mm longer than standard


Part Number

d1

l1 d2 l2 I3 max. I4 max.

d3
+ 0.12

SK552-040 4.0 4.5 2.50 69 9.0 6.5 4.0
SK552-050 5.0 5.5 3.00 71 10.0 7.5 5.0
SK552-060 6.0 6.5 3.40 73 12.0 8.0 6.0
SK552-070 7.0 7.5 4.10 68 14.0 9.0 7.0
SK552-080 8.0 8.5 4.20 70 15.0 10.5 8.0
SK552-090 9.0 9.5 4.50 73 17.0 11.0 9.0
SK552-100 10.0 10.5 4.75 75 19.0 12.5 10.0

Dimensions in mm

 

Pressure Performance

 

Series
SK
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 10     1.600 bar / 23.200 psi

   500 bar / 7.200 psi

    1.400 bar / 20.300 psi

   450 bar / 6.500 psi

 
 Proof Pressure Test

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation Instrution SK.pdf454.92 KB

Technical Information

Material:
Sleeve: Case hardening steel, soft annealed gun metal-finish
Mandrel: Heat treatable steel, special oil film lubrification


Part Number

d1

l1 d2 l2 I3 max. I4 max.

d3
+0.1

0

HK040CK55-211AK 4.0 5.0 2.2 68.0 9.5 8.0 4.0
HK050CK55-211AK 5.0 6.0 2.8 73.0 11.0 9.5 5.0
HK060CK55-211AK 6.0 6.5 2.8 73.0 12.0 10.0 6.0
HK070CK55-211AK 7.0 7.5 3.8 73.0 13.0 11.0 7.0
HK080CK55-211AK 8.0 8.5 4.5 68.0 13.5 11.5 8.0
HK090CK55-211AK 9.0 9.5 4.5 71.0 14.5 13.0 9.0
HK100CK55-211AK 10.0 10.5 4.5 71.0 15.5 13.5 10.0

Dimensions in mm

 

Pressure Performance

 

 

Series
SK
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
En-AC-42100
Ø 4– 10     1.200 bar / 17.400 psi

350 bar / 5.100 psi

    500 bar / 7.200 psi

160 bar / 2.300 psi

 
 Proof Pressure Test
Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionHK.pdf296.81 KB

Technical Information

Material:
Sleeve: Stainless steel, special oil film lubrification
Mandrel: Stainless steel, special oil film lubrification


Part Number

d1

l1

d2

l2

d3

+0.12

0

I3 max.

I4 max.

LK 600-040 4.0 3.7 2.2 33.0 4.0 6.05 4.0
LK 600-050 5.0 4.5 2.5 36.0 5.0 7.40 4.8
LK 600-060 6.0 5.0 3.2 36.0 6.0 8.20 5.5
LK 600-070 7.0 5.5 3.8 32.0 7.0 9.05 5.8
LK 600-080 8.0 6.5 4.3 34.0 8.0 10.75 7.0
LK 600-100 10.0 7.0 4.9 34.0 10.0 11.25 7.5

Dimensions in mm

 

Pressure Performance

 

Series
LK 600
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 10 180 bar / 2.600 psi

 

   60 bar / 850 psi

           
 Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Instaallation InstructionLK.pdf510.33 KB

Technical Information

Material:
Sleeve: Case hardening steel, soft aneealed gun finish
Mandrel: Steel, plain finish, special oil film lubrification


Part Number

d1

l1 d2 l2

d3

+0.12

0

I3 max. I4 max.
LK 950-040 4.0 3.7 2.2 36 4.0 5.5 4.0
LK 950-050 5.0 4.5 2.95 36 5.0 6.9 4.8
LK 950-060 6.0 5.0 3.4 36 6.0 7.7 5.3
LK 950-070 7.0 5.5 4.2 34 7.0 8.5 5.8
LK 950-080 8.0 6.5 4.3 34 8.0 9.8 6.8
LK 950-090 9.0 6.5 4.7 34 9.0 9.8 6.8
LK 950-100 10.0 6.5 5.1 36 10.0 9.8 6.8
LK 950-120 12.0 7.5 5.9 36 12.0 11.7 7.8
LK 950-140 14.0 8.0 5.9 36 14.0 12.2 8.7
LK 950-160 16.0 10.5 5.9 42 16.0 16.5 11.5
LK 950-180 18.0 12.0 6.15 46 18.0 18.6 13.0

Dimensions in mm

 

Pressure Performance

 

Series
LK 950
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 18 180 bar / 2.600 psi

 

   60 bar / 850 psi

           
 Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Instaallation InstructionLK.pdf510.33 KB

Technical Information

Material:
Free cutting steel, nitrocarburized, lubrificated


Part Number

d1

Expander

l2 l1

d3 min

d4

+0.1

-0.3

l2 min.
LP 900-040 4.40 3.7 5.0 4.55 4.0 7.0
LP 900-050 5.40 4.7 6.0 5.55 5.0 8.0
LP 900-060 6.40 5.7 6.0 6.55 6.0 8.5
LP 900-070 7.40 6.7 6.0 7.55 7.0 8.5
LP 900-080 8.45 7.7 7.0 8.6 8.0 9.5
LP 900-090 9.60 9.0 7.5 9.75 9.0 10.0
LP 900-100 10.65 10.0 8.5 10.8 10.0 11.0
LP 900-120 12.75 12.0 9.5 12.9 12.0 12.0

Dimensions in mm

 

Pressure Performance

Series

LP

mm

Base material of the Installation

ETG-100/44SMn28

AISI 1144

 C15Pb

1.0403

 EN-GJL-250

EN 1561

                 

 

     EN-GJS-500-700

 EN 1563           

       AICu4Mg1

EN AW-2024-T3

             AiMgSiPb

EN AW-6012-T6

 

          G-AiSi7Mg

EN AC-42100

Ø 4 - 12

180 bar / 2.600 psi

60 bar / 850 psi

           

Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

 

Operation

AttachmentSize
Installation Instruction_LP.pdf298.34 KB

Technical Information


行业

Industries

Our parts are proven reliable in a variety of industries and applications, including transportation, fluid power, precision and microhydraulics.

worldwide

Global presence

SFC KOENIG’s efficient business networks span the globe with locations in all key regions and a broad network of Distribution Partners.

certificates

certificates

Our sealing and flow control solutions comply with global quality assurance and certification standards.