Products

Material:
Sleeve: Stainless steel 1.4305
Ball: Stainless steel 1.4301










Part Number

d₁

Ø

I

I2 ~

Ref.

d

+0.10

d₃max.

I₃ min.

x

±0.2

MB 600-030 3.0 3.6 4.6 3.0 2.2 3.4 0.4
MB 600-040 4.0 4.0 5.1 4.0 3.3 3.8 0.2
MB 600-050 5.0 5.5 7.1 5.0 4.3 5.3 0.4
MB 600-060 6.0 6.5 8.6 6.0 5.3 6.3 0.4
MB 600-070 7.0 7.5 10.1 7.0 6.4 7.3 0.4
MB 600-080 8.0 8.5 11.6 8.0 7.4 8.3 0.3
MB 600-090 9.0 10.0 13.5 9.0 8.4 9.8 0.4
MB 600-100 10.0 11.0 15.1 10.0 9.4 10.8 0.4
MB 600-120 12.0 13.0 17.8 12.0 10.6 12.8 0.4
MB 600-140 14.0 15.0 20.5 14.0 12.7 14.5 0.4

Dimensions in mm

 

Pressure Performance

 

Series
MB 600
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AlMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 3 - 10     1.400 bar / 20.300 psi

   450 bar / 6.500 psi

    1.200 bar / 17.400 psi

   380 bar / 5.500 psi

 
Ø 12 - 14    

1.000 bar / 14.500 psi

   350 bar / 5.100 psi

   

900 bar / 13.000 psi

   280 bar / 4.100 psi

 
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Stainless steel 1.4305
Ball: Stainless steel 1.4301 (MB 600-093 - 1.4034)


Part Number

d1  

Ø

l1

l2 ~

Ref.

d2

d3 max

l3 min.

x

+0

-0.012

MB 600-093A 0.093 0.100 0.120 0.0937 0.062 0.095 0.012
MB 600-125A 0.125 0.138 0.170 0.1250 0.093 0.125 0.012
MB 600-156A 0.156 0.150 0.195 0.1562 0.125 0.130 0.012
MB 600-187A 0.187 0.193 0.260 0.1875 0.156 0.152 0.012
MB 600-218A 0.218 0.225 0.300 0.2187 0.187 0.187 0.012
MB 600-250A 0.250 0.260 0.350 0.2500 0.218 0.212 0.012
MB 600-281A 0.281 0.285 0.380 0.2812 0.250 0.250 0.012

Dimensions in inches

 

Pressure Performance

Series
MB 600
inch
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 0.093 - 0.281     1.400 bar / 20.300 psi

  450 bar / 6.500 psi

    1.200 bar / 17.400 psi

  380 bar / 5.500 psi

 
Proof Pressure Test

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Stainless steel 1.4305, plain finish
Ball: Bearing steel, heat treated


Part Number

d1 l1 l2 ~
Ref.

d2

+0,1

0

d3 max l3 min.

x

± -0.2

 MB 700-030 3.0 3.6 4.6 3.0 2.2 3.4 0.4
 MB 700-040 4.0 4.0 5.1 4.0 3.3 3.8 0.2
 MB 700-050 5.0 5.5 7.1 5.0 4.3 5.3 0.4
 MB 700-060 6.0 6.5 8.6 6.0 5.3 6.3 0.4
 MB 700-070 7.0 7.5 10.1 7.0 6.4 7.3 0.4
 MB 700-080 8.0 8.5 11.6 8.0 7.4 8.3 0.3
 MB 700-090 9.0 10.0 13.5 9.0 8.4 9.8 0.4
 MB 700-100 10.0 11.0 15.1 10.0 9.4 10.8 0.4
 MB 700-120 12.0 13.0 17.8 12.0 10.6 12.8 0.4
 MB 700-140 14.0 15.0 20.4 14.0 12.7 14.5 0.4
 MB 700-160 16.0 17.0 23.4 16.0 14.7 16.5 0.6
 MB 700-180 18.0 19.0 26.3 18.0 16.7 18.5 0.6
 MB 700-200 20.0 22.0 30.0 20.0 18.7 21.5 0.8
 MB 700-220 22.0 25.0 34.0 22.0 20.7 24.5 0.8

Dimensions in mm

 

Pressure Performance

 

 

Series
MB 700
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 3 - 10     1.400 bar / 20.300 psi

   450 bar / 6.500 psi

    1.200 bar / 17.400 psi

   380 bar / 5.500 psi

 
Ø 12 - 22    

1.150 bar / 16.700 psi

350 bar / 5.100 psi

   

900 bar / 13.000 psi

280 bar / 4.100 psi

 
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Case hardening steel zinc plated, thick coat passivated, CR (VI)-free
Ball: Bearing steel, heat treated


Part Number

d1

l1

l2 ~
Ref.

d2

+0,10

d3 max

l3 min.

x
± 0.2
 MB 850-030 3.0 3.6 4.6 3.0 2.2 3.4 0.4
 MB 850-040 4.0 4.0 5.2 4.0 3.3 3.8 0.2
 MB 850-050 5.0 5.5 7.1 5.0 4.3 5.3 0.4
 MB 850-060 6.0 6.5 8.6 6.0 5.3 6.3 0.4
 MB 850-070 7.0 7.5 10.1 7.0 6.4 7.3 0.4
 MB 850-080 8.0 8.5 11.6 8.0 7.4 8.3 0.3
 MB 850-090 9.0 10.0 13.6 9.0 8.4 9.8 0.4
 MB 850-100 10.0 11.0 15.1 10.0 9.4 10.8 0.4
 MB 850-120 12.0 13.0 17.9 12.0 10.6 12.8 0.4
 MB 850-140 14.0 15.0 20.6 14.0 12.7 14.5 0.4
 MB 850-160 16.0 17.0 23.4 16.0 14.7 16.5 0.6
 MB 850-180 18.0 19.0 26.4 18.0 16.7 18.5 0.6
 MB 850-200 20.0 22.0 30.1 20.0 18.7 21.5 0.8
 MB 850-220 22.0 25.0 34.0 22.0 20.7 24.5 0.8

Dimensions in mm

 

Pressure Performance

 

 

Series
MB 850
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 3 – 10     1.100 bar / 16.000 psi

   350 bar / 5.100 psi

    1.000 bar / 14.500 psi

   320 bar / 4.600 psi

 
Ø 12 - 22     900 bar / 13.000 psi
   280 bar / 4.100 psi
    800 bar / 11.600 psi

250 bar / 3.600 psi

 
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionMB.pdf674.21 KB

Technical Information

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6, Anodized Green, MIL-A-8625: Typ II, Class 2
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max. l3 min.

x

± 0.10

s
CV 143-030 3.0 3.18 4.1 3.0 2.3 2.9 0.2 1.0
CV 143-040 4.0 4.00 5.2 4.0 3.3 3.8 0.2 1.4
CV 143-050 5.0 5.50 7.0 5.0 4.3 5.3 0.2 1.9
CV 143-060 6.0 6.50 8.6 6.0 5.3 6.3 0.2 2.3
CV 143-070 7.0 7.50 10.1 7.0 6.2 7.3 0.2 2.8
CV 143-080 8.0 8.50 11.7 8.0 7.2 8.3 0.2 3.4
CV 143-090 9.0 10.0 13.7 9.0 8.2 9.8 0.2 3.7
CV 143-100 10.0 11.0 15.2 10.0 9.2 10.8 0.2 4.2
CV 143-120 12.0 13.0 18.0 12.0 11.0 12.8 0.2 5.1
CV 143-140 14.0 15.0 20.8 14.0 13.0 14.5 0.2 5.9
CV 143-160 16.0 17.0 23.7 16.0 14.7 16.5 0.2 6.4
CV 143-180 18.0 19.0 26.3 18.0 16.7 18.5 0.2 7.2
CV 143-200 20.0 22.0 30.5 20.0 18.7 21.5 0.2 8.4
CV 143-220 22.0 25.0 34.2 22.0 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 143
mm
Base material of the Installation
  AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10   170 bar / 2500 psi        
Ø 12 - 22            
Hole Tolerance     0 / + 0.1 mm      
Hole Roughness  Anchorage   Rz 10 - 30µm      

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Operation

AttachmentSize
Montagerichtlinien Serie CV DE.pdf173.32 KB

Technical Information

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6, allodined chromate conversion, MIL-C 5541
Ball: Stainless steel. AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max l3 min.

x

± 0.10

   s
CV 163-030 3.0 3.18 4.1 3.00 2.3 2.9 0.2 1.0
CV 163-040 4.0 4.00 5.2 4.00 3.3 3.8 0.2 1.4
CV163-050 5.0 5.50 7.0 5.00 4.3 5.3 0.2 1.9
CV 163-060 6.0 6.50 8.6 6.00 5.3 6.3 0.2 2.3
CV 163-070 7.0 7.50 10.1 7.00 6.2 7.3 0.2 2.8
CV 163-080 8.0 8.50 11.7 8.00 7.2 8.3 0.2 3.4
CV 163-090 9.0 10.00 13.7 9.00 8.2 9.8 0.2 3.7
CV 163-100 10.0 11.00 15.2 10.00 9.2 10.8 0.2 4.2
CV 163-120 12.0 13.00 18.0 12.00 11.0 12.8 0.2 5.1
CV 163-140 14.0 15.00 20.8 14.00 13.0 14.5 0.2 5.9
CV 163-160 16.0 17.00 23.7 16.00 14.7 16.5 0.2 6.4
CV 163-180 18.0 19.00 26.3 18.00 16.7 18.5 0.2 7.2
CV 163-200 20.0 22.00 30.5 20.00 18.7 21.5 0.2 8.4
CV 163-220 22.0 25.00 34.2 22.00 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 163
mm
Base material of the Installation
AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10   170 bar / 2500 psi      
Ø 12 - 22          
Hole Tolerance     0 / + 0.1 mm    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max l3 min.

x

± 0.10

 s
CV 173-030 3.0 3.18 4.1 3.00 2.3 2.9 0.2 1.0
CV 173-040 4.0 4.00 5.2 4.00 3.3 3.8 0.2 1.4
CV173-050 5.0 5.50 7.0 5.00 4.3 5.3 0.2 1.9
CV 173-060 6.0 6.50 8.6 6.00 5.3 6.3 0.2 2.3
CV 173-070 7.0 7.50 10.1 7.00 6.2 7.3 0.2 2.8
CV 173-080 8.0 8.50 11.7 8.00 7.2 8.3 0.2 3.4
CV 173-090 9.0 10.00 13.7 9.00 8.2 9.8 0.2 3.7
CV 173-100 10.0 11.00 15.2 10.00 9.2 10.8 0.2 4.2
CV 173-120 12.0 13.00 18.0 12.00 11.0 12.8 0.2 5.1
CV 173-140 14.0 15.00 20.8 14.00 13.0 14.5 0.2 5.9
CV 173-160 16.0 17.00 23.7 16.00 14.7 16.5 0.2 6.4
CV 173-180 18.0 19.00 26.3 18.00 16.7 18.5 0.2 7.2
CV 173-200 20.0 22.00 30.5 20.00 18.7 21.5 0.2 8.4
CV 173-220 22.0 25.00 34.2 22.00 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 173
mm
Base material of the Installation
AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10   170 bar / 2500 psi      
Ø 12 - 22          
Hole Tolerance     0 / + 0.1 mm    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (316) ASTM A580, passivate, QQ-P-35C
Ball: Stainless steel, AISI 316, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.10

-0.0

d3 max l3 min.

x

± 0.10

 s
CV 588-030 3.0 3.18 4.1 3.00 2.3 2.9 0.2 1.0
CV 588-040 4.0 4.00 5.2 4.00 3.3 3.8 0.2 1.4
CV 588-050 5.0 5.50 7.0 5.00 4.3 5.3 0.2 1.9
CV 588-060 6.0 6.50 8.6 6.00 5.3 6.3 0.2 2.3
CV 588-070 7.0 7.50 10.1 7.00 6.2 7.3 0.2 2.8
CV 588-080 8.0 8.50 11.7 8.00 7.2 8.3 0.2 3.4
CV 588-090 9.0 10.00 13.7 9.00 8.2 9.8 0.2 3.7
CV 588-100 10.0 11.00 15.2 10.00 9.2 10.8 0.2 4.2
CV  588-120 12.0 13.00 18.0 12.00 11.0 12.8 0.2 5.1
CV 588-140 14.0 15.00 20.8 14.00 13.0 14.5 0.2 5.9
CV 588-160 16.0 17.00 23.7 16.00 14.7 16.5 0.2 6.4
CV 588-180 18.0 19.00 26.3 18.00 16.7 18.5 0.2 7.2
CV 588-200 20.0 22.00 30.5 20.00 18.7 21.5 0.2 8.4
CV 588-220 22.0 25.00 34.2 22.00 20.7 24.5 0.2 9.5

Dimensions in mm

 

Pressure Performance

Series
CV 588
mm
Base material of the Installation
AI A356 Al 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 3 - 10     450 bar / 6500 psi    
Ø 12 - 22          
Hole Tolerance     0 / + 0.1 mm    
Hole Roughness  Anchorage       Rz 10 -30µm

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-Q 225/6, anodized green, MIL-A-8625: Type II, Class 2
Ball: Stainless steel, AISI 302/304, wax film lubrication (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 143-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 143-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV143-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 143-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 143-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 143-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 143-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 143-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 143-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 143-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 143-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 143-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 143-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 143-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 143-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV 143-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 143
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375   170 bar / 2500 psi      
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A-225/6, allodined chromate, MIL-C 5541
Ball: Stainless steel, AISI 302/304, wax film lubrication (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.0040

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 163-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 163-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV163-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 163-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 163-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 163-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 163-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 163-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 163-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 163-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 163-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 163-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 163-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 163-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 163-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV 163-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 163
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375   170 bar / 2500 psi      
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (303), ASTM A582
Ball: Bearing steel, heat treated, black oxide & wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 531-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 531-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV 531-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 531-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 531-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 531-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 531-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 531-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 531-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 531-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 531-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 531-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 531-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 531-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 531-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV 531-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 531
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375     450 bar / 6500 psi    
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (316) ASTM A580, passivate, QQ-P-35C
Ball: Stainless steel, AISI 316, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

 s
CV 588-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 588-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV 588-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 588-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 588-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 588-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 588-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 588-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 588-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 588-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 588-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 588-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 588-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 588-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 588-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV  588-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 588
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375     450 bar / 6500 psi    
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Case hardening steel ASTM A108, zinc chromate ASTM B633: Type III, trivalent
Ball: Bearing steel, heat treated, black oxide & wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 851-156 0.156 0.158 .21 0.1562 0.130 0.149 0.008 0.053
CV 851-187 0.187 0.217 .27 0.1875 0.160 0.208 0.010 0.066
CV 851-218 0.218 0.217 .28 0.2187 0.190 0.208 0.010 0.078
CV 851-250 0.250 0.256 .34 0.2500 0.220 0.247 0.010 0.094
CV 851-281 0.281 0.296 .40 0.2812 0.250 0.287 0.010 0.110
CV 851-312 0.312 0.335 .46 0.3125 0.281 0.326 0.010 0.129
CV 851-343 0.343 0.394 .52 0.3437 0.312 0.385 0.010 0.140
CV 851-375 0.375 0.394 .54 0.3750 0.343 0.385 0.010 0.153
CV 851-406 0.406 0.434 .59 0.4062 0.375 0.425 0.010 0.162
CV 851-437 0.437 0.512 .68 0.4375 0.406 0.503 0.010 0.166
CV 851-468 0.468 0.512 .71 0.4687 0.437 0.503 0.010 0.199
CV 851-562 0.562 0.591 .82 0.5625 0.510 0.570 0.010 0.233
CV 851-625 0.625 0.669 .91 0.6250 0.562 0.649 0.010 0.252
CV 851-687 0.687 0.748 1.03 0.6875 0.625 0.727 0.010 0.289
CV 851-750 0.750 0.866 1.18 0.7500 0.688 0.845 0.010 0.317
CV  851-875 0.875 0.984 1.35 0.8750 0.813 0.963 0.010 0.354

Dimensions in inches

Pressure Performance

Series
CV 851
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.156 - 0.375     450 bar / 6500 psi    
Ø 0.406 - 0.875          
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A 225/6, anodized green, MIL-A-8625: Type II, Class 2
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 143-125S 0.125 0.125 .16 0.1250 0.100 0.113 0.007 0.042
CV 143-156S 0.156 0.125 .17 0.1562 0.130 0.113 0.000 0.040
CV143-187S 0.187 0.187 .24 0.1875 0.160 0.170 0.010 0.066
CV 143-218S 0.218 0.187 .25 0.2187 0.190 0.170 0.000 0.063
CV 143-250S 0.250 0.225 .30 0.2500 0.220 0.196 0.000 0.083
CV 143-281S 0.281 0.255 .35 0.2812 0.250 0.233 0.000 0.091
CV 143-312S 0.312 0.280 .39 0.3125 0.281 0.255 0.000 0.107
CV 143-343S 0.343 0.307 .43 0.3437 0.312 0.275 0.000 0.118
CV 143-406S 0.406 0.365 .52 0.4062 0.375 0.308 0.010 0.143

Dimensions in inches

Pressure Performance

Series
CV 143 Short
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.125 - 0.406   120 bar / 1750 psi      
Hole Tolerance     Ø 0.125:0 / +0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Aluminum 2024-T4, QQ-A-225/6, allodined chromate conversion, MIL-C 5541
Ball: Stainless steel, AISI 302/304, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 163-125S 0.125 0.125 .16 0.1250 0.100 0.113 0.007 0.042
CV 163-156S 0.156 0.125 .17 0.1562 0.130 0.113 0.000 0.040
CV163-187S 0.187 0.187 .24 0.1875 0.160 0.170 0.010 0.066
CV 163-218S 0.218 0.187 .25 0.2187 0.190 0.170 0.000 0.063
CV 163-250S 0.250 0.225 .30 0.2500 0.220 0.196 0.000 0.083
CV 163-281S 0.281 0.255 .35 0.2812 0.250 0.233 0.000 0.091
CV 163-312S 0.312 0.280 .39 0.3125 0.281 0.255 0.000 0.107
CV 163-343S 0.343 0.307 .43 0.3437 0.312 0.275 0.000 0.118
CV 163-406S 0.406 0.365 .52 0.4062 0.375 0.308 0.010 0.143

Dimensions in inches

Pressure Performance

Series
CV 163 Short
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.125 - 0.406   120 bar / 1750 psi      
Hole Tolerance     Ø 0.125:0 / +0.004 in.    
Hole Roughness  Anchorage   Rz 10 - 30µm    

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Stainless steel (316) ASTM A580, passivate, QQ-P-35C
Ball: Stainless steel, AISI 316, wax film lubrification (diameter dependant)


Part Number d1 l1 l2 ~
Ref.

d2

+0.004

-0.0

d3 max l3 min.

x

± 0.004

s
CV 588-125S 0.125 0.125 .16 0.1250 0.100 0.113 0.007 0.042
CV 588-156S 0.156 0.125 .17 0.1562 0.130 0.113 0.000 0.040
CV588-187S 0.187 0.187 .24 0.1875 0.160 0.170 0.010 0.066
CV 588-218S 0.218 0.187 .25 0.2187 0.190 0.170 0.000 0.063
CV 588-250S 0.250 0.225 .30 0.2500 0.220 0.196 0.000 0.083
CV 588-281S 0.281 0.255 .35 0.2812 0.250 0.233 0.000 0.091
CV 588-312S 0.312 0.280 .39 0.3125 0.281 0.255 0.000 0.107
CV  588-343S 0.343 0.307 .43 0.3437 0.312 0.275 0.000 0.118
CV 588-406S 0.406 0.365 .52 0.4062 0.375 0.308 0.010 0.143

Dimensions in inches

Pressure Performance

Series
CV 588 Short
in.
Base material of the Installation
AI A356 AL 2024-T4 CI 60-45-12 CI GJS 600 Steel ETG-100
Ø 0.125 - 0.406   250 bar / 3600 psi      
Hole Tolerance     0 / + 0.004 in.    
Hole Roughness  Anchorage in Base Material       Rz 10 - 30µm

Max. allowable Working Pressure = Nominal Pressure

Please note these recommendations are generally conservtive, and higher working pressures are possible in some applications. Please contact your local applications engineer with any questions.

Material:
Sleeve: Case hardening steel, gun metal-finish
Mandrel: Heat treatable steel, special oil film lubrification


Part Number

d1

l1 d2 l2 I3 max. I4 max.

d3
+ 0.120

SK550-040 4.0 4.5 2.50 39 9.0 6.5 4.0
SK550-050 5.0 5.5 3.00 41 10.0 7.5 5.0
SK550-060 6.0 6.5 3.40 43 12.0 8.0 6.0
SK550-070 7.0 7.5 4.10 38 14.0 9.0 7.0
SK550-080 8.0 8.5 4.20 40 15.0 10.5 8.0
SK550-090 9.0 9.5 4.50 43 17.0 11.0 9.0
SK550-100 10.0 10.5 4.75 45 19.0 12.5 10.0
SK550-120 12.0 12.5 5.7 50 24.0 16.50 12.0

Dimensions in mm

Pressure Performance

Series
SK
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 10     1.600 bar / 23.200 psi

   500 bar / 7.200 psi

    1.400 bar / 20.300 psi

   450 bar / 6.500 psi

 

 
Ø 12     1.600 bar / 23.200 psi

   400 bar / 5.800 psi

       
Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation Instrution SK.pdf454.92 KB

Technical Information

Material:
Sleeve: Case hardening steel, gun metal-finish
Mandrel: Heat treatable steel, special oil film lubrification

One piece construction, ideal for automated high production requirements

Special Type: with mandrel 30mm longer than standard


Part Number

d1

l1 d2 l2 I3 max. I4 max.

d3
+ 0.12

SK552-040 4.0 4.5 2.50 69 9.0 6.5 4.0
SK552-050 5.0 5.5 3.00 71 10.0 7.5 5.0
SK552-060 6.0 6.5 3.40 73 12.0 8.0 6.0
SK552-070 7.0 7.5 4.10 68 14.0 9.0 7.0
SK552-080 8.0 8.5 4.20 70 15.0 10.5 8.0
SK552-090 9.0 9.5 4.50 73 17.0 11.0 9.0
SK552-100 10.0 10.5 4.75 75 19.0 12.5 10.0

Dimensions in mm

 

Pressure Performance

 

Series
SK
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 10     1.600 bar / 23.200 psi

   500 bar / 7.200 psi

    1.400 bar / 20.300 psi

   450 bar / 6.500 psi

 
 Proof Pressure Test

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation Instrution SK.pdf454.92 KB

Technical Information

Material:
Sleeve: Case hardening steel, soft annealed gun metal-finish
Mandrel: Heat treatable steel, special oil film lubrification

d1 Ø3: Sleeve and Mandrel not pre-assembled


Part Number

d1

l1 d2 l2 I3 max. I4 max.

d3
+0.1

0

HK030CK55-111 3.0 5.0 2.0 36.5 9.0 7.0 3.0
HK040CK55-111AK 4.0 5.0 2.2 38.0 9.5 8.0 4.0
HK050CK55-111AK 5.0 6.0 2.8 43.0 11.0 9.5 5.0
HK060CK55-111AK 6.0 6.5 2.8 43.0 12.0 10.0 6.0
HK070CK55-111AK 7.0 7.5 3.8 43.0 13.0 11.0 7.0
HK080CK55-111AK 8.0 8.5 4.5 38.0 13.5 11.5 8.0
HK090CK55-111AK 9.0 9.5 4.5 41.0 14.5 13.0 9.0
HK100CK55-111AK 10.0 10.5 4.5 41.0 15.5 13.5 10.0

Dimensions in mm

 

Pressure Performance

Series
HK
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
En-AC-42100
Ø 3 – 10     1.200 bar / 17.400 psi
   350 bar / 5.100 psi
    500 bar / 7.200 psi
   160 bar / 2.300 psi
 
 Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionHK.pdf296.81 KB

Technical Information

Material:
Sleeve: Case hardening steel, soft annealed gun metal-finish
Mandrel: Heat treatable steel, special oil film lubrification


Part Number

d1

l1 d2 l2 I3 max. I4 max.

d3
+0.1

0

HK040CK55-211AK 4.0 5.0 2.2 68.0 9.5 8.0 4.0
HK050CK55-211AK 5.0 6.0 2.8 73.0 11.0 9.5 5.0
HK060CK55-211AK 6.0 6.5 2.8 73.0 12.0 10.0 6.0
HK070CK55-211AK 7.0 7.5 3.8 73.0 13.0 11.0 7.0
HK080CK55-211AK 8.0 8.5 4.5 68.0 13.5 11.5 8.0
HK090CK55-211AK 9.0 9.5 4.5 71.0 14.5 13.0 9.0
HK100CK55-211AK 10.0 10.5 4.5 71.0 15.5 13.5 10.0

Dimensions in mm

 

Pressure Performance

 

 

Series
SK
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
En-AC-42100
Ø 4– 10     1.200 bar / 17.400 psi

350 bar / 5.100 psi

    500 bar / 7.200 psi

160 bar / 2.300 psi

 
 Proof Pressure Test
Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Installation InstructionHK.pdf296.81 KB

Technical Information

Material:
Sleeve: Stainless steel, special oil film lubrification
Mandrel: Stainless steel, special oil film lubrification


Part Number

d1

l1

d2

l2

d3

+0.12

0

I3 max.

I4 max.

LK 600-040 4.0 3.7 2.2 33.0 4.0 6.05 4.0
LK 600-050 5.0 4.5 2.5 36.0 5.0 7.40 4.8
LK 600-060 6.0 5.0 3.2 36.0 6.0 8.20 5.5
LK 600-070 7.0 5.5 3.8 32.0 7.0 9.05 5.8
LK 600-080 8.0 6.5 4.3 34.0 8.0 10.75 7.0
LK 600-100 10.0 7.0 4.9 34.0 10.0 11.25 7.5

Dimensions in mm

 

Pressure Performance

 

Series
LK 600
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 10 180 bar / 2.600 psi

 

   60 bar / 850 psi

           
 Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Instaallation InstructionLK.pdf510.33 KB

Technical Information

Material:
Sleeve: Case hardening steel, soft aneealed gun finish
Mandrel: Steel, plain finish, special oil film lubrification


Part Number

d1

l1 d2 l2

d3

+0.12

0

I3 max. I4 max.
LK 950-040 4.0 3.7 2.2 36 4.0 5.5 4.0
LK 950-050 5.0 4.5 2.95 36 5.0 6.9 4.8
LK 950-060 6.0 5.0 3.4 36 6.0 7.7 5.3
LK 950-070 7.0 5.5 4.2 34 7.0 8.5 5.8
LK 950-080 8.0 6.5 4.3 34 8.0 9.8 6.8
LK 950-090 9.0 6.5 4.7 34 9.0 9.8 6.8
LK 950-100 10.0 6.5 5.1 36 10.0 9.8 6.8
LK 950-120 12.0 7.5 5.9 36 12.0 11.7 7.8
LK 950-140 14.0 8.0 5.9 36 14.0 12.2 8.7
LK 950-160 16.0 10.5 5.9 42 16.0 16.5 11.5
LK 950-180 18.0 12.0 6.15 46 18.0 18.6 13.0

Dimensions in mm

 

Pressure Performance

 

Series
LK 950
mm
Base material of the Installation
1 ETG-100 / 44SMn28
AISI 1144
2 C15Pb
1.0403
3 EN-GJL-250
EN 1561
4 EN-GJS-500-7
EN 1563
5 AICu4Mg1
EN AW-2024-T3
6 AIMgSiPb
EN AW-6012-T6
7 G-AISi7Mg
EN-AC-42100
Ø 4 – 18 180 bar / 2.600 psi

 

   60 bar / 850 psi

           
 Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

Operation

AttachmentSize
Instaallation InstructionLK.pdf510.33 KB

Technical Information

Material:
Free cutting steel, nitrocarburized, lubrificated


Part Number

d1

Expander

l2 l1

d3 min

d4

+0.1

-0.3

l2 min.
LP 900-040 4.40 3.7 5.0 4.55 4.0 7.0
LP 900-050 5.40 4.7 6.0 5.55 5.0 8.0
LP 900-060 6.40 5.7 6.0 6.55 6.0 8.5
LP 900-070 7.40 6.7 6.0 7.55 7.0 8.5
LP 900-080 8.45 7.7 7.0 8.6 8.0 9.5
LP 900-090 9.60 9.0 7.5 9.75 9.0 10.0
LP 900-100 10.65 10.0 8.5 10.8 10.0 11.0
LP 900-120 12.75 12.0 9.5 12.9 12.0 12.0

Dimensions in mm

 

Pressure Performance

Series

LP

mm

Base material of the Installation

ETG-100/44SMn28

AISI 1144

 C15Pb

1.0403

 EN-GJL-250

EN 1561

                 

 

     EN-GJS-500-700

 EN 1563           

       AICu4Mg1

EN AW-2024-T3

             AiMgSiPb

EN AW-6012-T6

 

          G-AiSi7Mg

EN AC-42100

Ø 4 - 12

180 bar / 2.600 psi

60 bar / 850 psi

           

Proof Pressure Test B

Max. allowable Working Pressure = Nominal Pressure

 

Operation

AttachmentSize
Installation Instruction_LP.pdf298.34 KB

Technical Information

Material:

Sleeve: Stainless Steel, 1.4305 (AISI 303)

Pin: Stainless Steel, 1.4542 (AISI 630)

Ball: Bearing Steel, 1.3541 (AISI 420C)

Spring: Stainless Steel, 1.4310 (AISI 301)

Cage: Stainless Steel, 1.4310 (AISI 301)


Type

 

d1

 

l1

 

d2

+0.1

0

 

l2

 

d3

(l3)

 

d4

max.

l4

max.

l5

min.

O

 

X

±0.15

S

Cracking

Pressure

(bar)

BF660080024000 8.0 10.0 8.0 3.8 7.0 13.8 3.8 3.2 10.0 2.4 0.15 4.0 0 (No spring)
BF660080024014 8.0 10.0 8.0 3.8 7.0 13.8 3.8 3.2 10.0 2.4 0.15 4.0 0.14 (± 0.05)
BF660080024040 8.0 10.0 8.0 3.8 7.0 13.8 3.8 3.2 10.0 2.4 0.15 4.0 0.4 (± 0.3)
BF660080024100 8.0 10.0 8.0 3.8 7.0 13.8 3.8 3.2 10.0 2.4 0.15 4.0 1.0 (± 0.3)

Pressure Performance

Installation force * Max. 18 kN
Anchorage principles Force based (roughness)
Max. working pressure differential * 300 bar / 4350 psi checked direction, 40 bar / 580 psi flow direction
Operating temperature -40° to 150°C (ETG-100, 1.4305, AA2024); -40° to 100°C (AA356, GJS-600)
Cycle-testing (Oil HLP 46) 1 Mio cycles, 5 Hz, 6 bar
Max. leakage rate (Air) 15 sccm/min @ 1.72 bar (172 kPa)
Medium Oil, Water, Air

*Test material: ETG-100, GJS-600, 1.4305, AA356, AA2024 (Avional)

VALVE CHARACTERISTIC CURVE

Flow Curve for 1 bar Valve

Operation

AttachmentSize
Installation Instructions CV EN.pdf153.67 KB

Material:

Sleeve: Stainless Steel, 1.4305 (AISI 303)

Pin: Stainless Steel, 1.4542 (AISI 630)

Ball: Bearing Steel, 1.3541 (AISI 420C)

Spring: Stainless Steel, 1.4310 (AISI 301)

Cage: Stainless Steel, 1.4310 (AISI 301)


Type

 

d1

 

l1

 

d2

+0.1

0

 

l2

 

d3

(l3)

 

l5

min.

O

 

X

±0.15

S

Cracking

Pressure

(bar)

 

BR660080024000 8.0 10.0 8.0 3.8 7.0 13.8 10.0 2.4 0.15 4.0 0 (No spring)
BR660080024014 8.0 10.0 8.0 3.8 7.0 13.8 10.0 2.4 0.15 4.0 0.14 (± 0.05)
BR660080024040 8.0 10.0 8.0 3.8 7.0 13.8 10.0 2.4 0.15 4.0 0.4 (± 0.3)
BR660080024100 8.0 10.0 8.0 3.8 7.0 13.8 10.0 2.4 0.15 4.0 1.0 (± 0.3)

Pressure Performance

Installation force * Max. 18 kN
Anchorage principles Force based (roughness)
Max. working pressure differential * 300 bar / 4350 psi checked direction, 40 bar / 580 psi flow direction
Operating temperature -40° to 150°C (ETG-100, 1.4305, AA2024); -40° to 100°C (AA356, GJS-600)
Cycle-testing (Oil HLP 46) 1 Mio cycles, 5 Hz, 6 bar
Max. leakage rate (Air) 15 sccm/min @ 1.72 bar (172 kPa)
Medium Oil, Water, Air

*Test material: ETG-100, GJS-600, 1.4305, AA356, AA2024 (Avional)

VALVE CHARACTERISTIC CURVE

Flow Curve for 1 bar Valve

Operation

AttachmentSize
Installation Instructions CV EN.pdf153.67 KB

Material:

Sleeve: Stainless Steel, 1.4305 (AISI 303)

Pin: Stainless Steel, 1.4021 (AISI 420)

Ball: Bearing Steel, 1.3541 (AISI 420C)

Spring: Stainless Steel, 1.4310 (AISI 301)

Cage: Stainless Steel, 1.4310 (AISI 301)


Type

 

d1

 

l1

 

d2

+0.1

0

 

l2

 

d3

(l3)

l5

min.

O

 

X

±0.15

S

Cracking

Pressure

(bar)

BR055U000 5.5 7.0 5.5 2.0 4.0 9.0 7.0 1.7 0.15 2.2 0 (No spring)
BR055U014 5.5 7.0 5.5 2.0 4.0 9.0 7.0 1.7 0.15 2.2 0.14 (± 0.05)
BR055U025 5.5 7.0 5.5 2.0 4.0 9.0 7.0 1.7 0.15 2.2 0.25 (± 0.1)
BR055U040 5.5 7.0 5.5 2.0 4.0 9.0 7.0 1.7 0.15 2.2 0.4 (± 0.3)
BR055U100 5.5 7.0 5.5 2.0 4.0 9.0 7.0 1.7 0.15 2.2 1.0 (± 0.3)
BR055U200 5.5 7.0 5.5 2.0 4.0 9.0 7.0 1.7 0.15 2.2 2.0 (± 0.3)

Pressure Performance

Installation force * Max. 18 kN
Anchorage principles Force based (roughness)
Max. working pressure differential * 300 bar / 4350 psi checked direction, 40 bar / 580 psi flow direction**
Operating temperature -40° to 150°C (ETG-100, 1.4305, AA2024); -40° to 100°C (AA356, GJS-600)
Cycle-testing (Oil HLP 46) 1 Mio cycles, 5 Hz, 6 bar
Max. leakage rate (Air) 15 sccm/min @ 1.72 bar (172 kPa)
Medium Oil, Water, Air

*Test material: ETG-100, GJS-600, 1.4305, AA356, AA2024 (Avional)

**Part BR055U014, 30 bar / 440 psi in Flow Direction

VALVE CHARACTERISTIC CURVE

Flow Curve for 1 bar Valve

Operation

AttachmentSize
Installation Instructions CV EN.pdf153.67 KB

PART NUMBER KEY: XXX is the orifice Diameter in hundreths of a Millimeter Example: Ø 1.27mm orifice will be 127. Ø 0.40mm orifice will be 040.

+ ALL DIMENSION IN MM

Determine Orifice Size & Flow Rate
+ Flow Rate Calculator - mm
+ Flow Rate Calculator - Inch
+ Orifice Size Calculator - mm
+ Orifice Size Calculator - Inch


Part Number

d1

l1

l2 ~

Ref.

0

±0.025

Orifice Diameter

d2

+0.10

-0

l3 min.

 s

 x

±0.3

 d3 max.

RE-040-XXX 4.0 4.0 6.0 0.40 - 1.25 4.0 3.9 2.0 0.0 3.3
RE-050-XXX 5.0 5.5 8.2 0.40 - 1.90 5.0 5.4 2.7 0.0 4.3
RE-060-XXX 6.0 6.5 9.9 0.40 - 2.50 6.0 6.4 3.4 0.0 5.3
RE-070-XXX 7.0 7.5 11.6 0.40 - 3.30 7.0 7.4 4.1 0.0 6.2
RE-080-XXX 8.0 8.5 13.3 0.40 - 3.80 8.0 8.4 4.8 0.0 7.2
RE-090-XXX 9.0 10.0 15.5 0.40 - 4.30 9.0 9.9 5.5 0.0 8.2
RE-100-XXX 10.0 11.0 17.1 0.40 - 4.95 10.0 10.9 6.1 0.0 9.2
RE-120-XXX 12.0 13.0 20.5 0.40 - 6.10 12.0 12.9 7.5 0.0 11.0
RE-140-XXX 14.0 15.0 23.7 0.40 - 7.10 14.0 14.9 8.7 0.0 13.0

Dimensions in mm

Pressure Performance

Series

RE

mm

Base material of the Installation

ETG-100/44SMn28

AISI 1144

 C15Pb

1.0403

 EN-GJL-250

EN 1561

     EN-GJS-500-700

EN 1563

AICu4Mg1

EN AW-2024-T3

AiMgSiPb

EN AW-6012-T6

G-AlSi7Mg

EN-AC-42100

Ø 4 - 14 200 bar / 2940 psi           150 bar / 2205 psi

Max. Allowable Working Pressure = Nominal Pressure   

PART NUMBER KEY: XXX is the orifice diameter in thousandths of a Millimeter. Example: Ø 0.050 Inch orifice will be 050.

+ ALL DIMENSIONS IN INCH

Determine Orifice Size & Flow Rate
+ Flow Rate Calculator - mm
+ Flow Rate Calculator - Inch
+ Orifice Size Calculator - mm
+ Orifice Size Calculator - Inch


Part Number

d1

l1

l2 ~

Ref.

0

±0.001

Orifice Diameter

d2

+0.004

-0

l3 min.

 s

 x

±0.01

 d3 max.

RE 156-XXX 0.156 0.158 0.24 .020 - .050 0.1563 0.15 0.03 0.0 0.130
RE 187-XXX 0.187 0.217 0.31 .020 - .070 0.1875 0.21 0.04 0.0 0.160
RE 218-XXX 0.218 0.217 0.33 .020 - .085 0.2188 0.21 0.05 0.0 0.190
RE 250-XXX 0.250 0.256 0.40 .020 - .105 0.2500 0.25 0.08 0.0 0.220
RE 281-XXX 0.281 0.296 0.46 .020 - .130 0.2813 0.29 0.10 0.0 0.250
RE 312-XXX 0.312 0.335 0.52 .020 - .150 0.3125 0.33 0.12 0.0 0.281
RE 343-XXX 0.343 0.394 0.60 .020 - .160 0.3438 0.39 0.13 0.0 0.312
RE 375-XXX 0.375 0.394 0.62 .020 - .180 0.3750 0.39 0.16 0.0 0.343
RE 406-XXX 0.406 0.434 0.67 .020 - .195 0.4063 0.43 0.15 0.0 0.375
RE 437-XXX 0.437 0.512 0.77 .020 - 220 0.4375 0.51 0.17 0.0 0.406
RE 468-XXX 0.468 0.512 0.81 .020 - .240 0.4688 0.51 0.20 0.0 0.437
RE 562-XXX 0.562 0.591 0.94 .020 - .290 0.5625 0.59 0.24 0.0 0.510

Dimensions in inch

 

Pressure Performance

Series

RE

inch

Base material of the Installation

ETG-100/44SMn28

AISI 1144

 C15Pb

1.0403

 EN-GJL-250

EN 1561

     EN-GJS-500-700

 EN 1563

AICu4Mg1

EN AW-2024-T3

AiMgSiPb

EN AW-6012-T6

G-AlSi7Mg

EN-AC-42100

Ø 0.156 - 0.562 200 bar / 2940 psi           150 bar / 2205 psi

Max. Allowable Working Pressure = Nominal Pressure   

Hydropneumatic setting tool for the installation of KOENIG expanders, series MB und LP from Ø 3-10 mm. Quick tool change avoids long changeover times. The required working stroke is preprogrammed and can be retrieved by the expander type to be processed (max. 32 memory locations). In addition, the working stroke is referenced for each individual expader, which guarantees high process stability and quality. The press is force and distance controlled; an RS232 interface can be used to trace corresponding data on the customer's computer for later processing. The required software is included in the scope of delivery.

Technical Data

EXPRESS 3000

Height approx. 1360 mm
Width approx. 340 mm (max. 530 mm)
Depth approx. 495 mm
Working area (height) 250 mm ( working height between table top and cylinder, without setting tool)
Working area ( depth) 200 mm (center- line spacing between cylinder and C frame)
Table (width x depth) 220 x 160 mm
Weight approx. 140 kg
Compressive force 30 kN (max. force 29.5 kN at 6 bar)
Cylinder ram 60 mm
Working stroke 10 mm (within the cylinder ram)
Working speed 40 mm / sec (max. possible at 6 bar)
Operating voltage 230 V / 110 V,Automatic switchmatic to corresponding power supply
Operation VISUAL POINT terminal with QVGA graphic display  
Force / distance Sensor adjusted with SIT reference sensor
Software WINSCOPE Software for connecting to a PC
Hydropneumatic setting tool for the installation of KOENIG expanders, series MB und LP from Ø 12-22 mm. Quick tool change avoids long changeover times. The required working stroke is preprogrammed and can be retrieved by the Expander type to be processed (max. 32 memory locations). In addition, the working stroke is referenced for each individual Expander, which guarantees high process stability and quality. The press is force and distance controlled; an RS232 interface can be used to trace corresponding data on the customer's computer for later processing. The required software is included in the scope of delivery.

Technical Data

EXPRESS 5000

Height approx. 1470 mm
Width approx. 400 mm (max. 580 mm)
Depth approx. 535 mm
Working area (height) 250 mm ( working height between table top and cylinder, without setting tool)
Working area ( depth) 200 mm (center- line spacing between cylinder and C frame)
Table (width x depth) 300 x 190 mm
Weight approx. 190 kg
Compressive force 50 kN (max. force 52.5 kN at 6 bar)
Cylinder ram 60 mm
Working stroke 15 mm (within the cylinder ram)
Working speed 30 mm / sec (max. possible at 6 bar)
Operating voltage 230 V / 110 V,Automatic switchmatic to corresponding power supply
Operation VISUAL POINT terminal with QVGA graphic display  
Force / distance Sensor adjusted with SIT reference sensor
Software WINSCOPE Software for connecting to a PC

 Technical Data EXTOOL-030
Weight 2.5 kg
Pull force at 7 bar 19.0 kN
Working stroke 25 mm
Air supply pressure (min. - max.) 5 - 7 bar
Air consumption at 5-6 bar 3.5I
Noise Level < 75 dB (A)
Cycle Time 2.0 s

Expander

Ø

 Nose Piece

(not included)

Part Number

4.0 361013304100
5.0 361013305100
6.0 361013306100
 

 Jaws

Part Number

4.0 - 6.0 361130400504
  Jaw Case
Part Number
4.0 - 6.0 321120000012
 

Jaw Pusher

Part Number

4.0 - 6.0 361013304010

 Technical Data EXTOOL-040-1
Weight 2.7 kg
Pull force at 7 bar 24.0 kN
Working stroke 18 mm
Air supply pressure (min. - max.) 5 - 7 bar
Air consumption at 5-6 bar 3.5I
Noise Level < 75 dB (A)
Cycle Time 2.0 s

Expander

Ø

 Nose Piece

(not included)

Part Number

7.0 361013307100
8.0 361013308100
9.0 361013309100
10.0 361013310100
 

 Jaws

Part Number

7.0 - 10.0 361130400507-3-1
  Jaw Case
Part Number
7.0 - 10.0 361059120013
 

Jaw Pusher

Part Number

7.0 - 10.0 361013307010

 Technical Data KW - 002
Weight  0.6 kg

Expander

Ø

 Nose Piece

Part Number

3.0 HKW-002103
4.0 HKW-002104
 

 Jaws

Part Number

3.0 - 4.0 15068
Hand Lever tool with Equipment HK Ø 4 - 6 mm

 Technical Data KW - 008
Weight  1.95 kg
Length 515 mm

Expander

Ø

 Nose Piece

Part Number

3.0 / 4.0 DPM400-B10
5.0 / 6.0 DPM400-C10
 

 Jaws

Part Number

3.0 - 6.0 PRG 540-46E

Material:
Steel, Heat treated, hardness approx. HRC 50


Part Number

d1

Expander Ø

d- h9 l1 d2 I2 x
± 0.2
MB 030 3.0 10 100 2.8 10 0.4
MB 040 4.0 10 100 3.8 10 0.2
MB 050 5.0 10 100 4.8 12 0.4
MB 060 6.0 10 100 5.8 15 0.4
MB 070 7.0 10 100 6.8 18 0.4
MB 080 8.0 10 100 7.8 20 0.3
MB 090 9.0 14 100 8.8 22 0.4
MB 100 10.0 14 100 9.8 25 0.4
MB 120 12.0 14 150 11.7 30 0.4
MB 140 14.0 20 150 13.7 35 0.4
MB 160 16.0 20 150 15.7 40 0.6
MB 180 18.0 20 150 17.7 45 0.6
MB 200 20.0 25 150 19.7 50 0.8
MB 220 22.0 25 150 21.7 55 0.8

Material:
Steel, Heat treated, hardness approx. HRC 50


Part Number

d1

Expander Ø

d- h9 l1 d2 I2 x
-0.012
MB 093A 0.093 0.394 3.94 0.082 0.137 0.012
MB 125A 0.125 0.394 3.94 0.117 0.137 0.012
MB 156A 0.156 0.394 3.94 0.148 0.137 0.012
MB 187A 0.187 0.394 3.94 0.180 0.137 0.012
MB 218A 0.218 0.394 3.94 0.211 0.400 0.012
MB 250A 0.250 0.394 3.94 0.242 0.400 0.012
MB 281A 0.281 0.394 3.94 0.273 0.400 0.012

Material:
Steel, Heat treated, hardness approx. HRC 50


Part Number

d1

Expander

d

± 0.12

l1 d2 I2 x
± 0.10
s
HT-MBM-030 MB/CV XXX-30 9.53 127 2.8 7.6 0.2 1.0
HT-MBM-040 MB/CV XXX-40 9.53 127 3.8 7.6 0.2 1.4
HT-MBM-050 MB/CV XXX-50 9.53 127 4.8 12.7 0.2 1.9
HT-MBM-060 MB/CV XXX-60 9.53 127 5.8 15.2 0.2 2.3
HT-MBM-070 MB/CV XXX-70 9.53 127 6.8 20.3 0.2 2.8
HT-MBM-080 MB/CV XXX-80 9.53 127 7.8 33.0 0.2 3.4
HT-MBM-090 MB/CV XXX-90 12.70 127 8.8 38.1 0.2 3.7
HT-MBM-100 MB/CV XXX-100 12.70 127 9.8 38.1 0.2 4.2
HT-MBM-120 MB/CV XXX-120 12.70 127 11.7 38.1 0.2 5.1
HT-MBM-140 MB/CV XXX-140 15.88 127 13.7 45.7 0.2 5.9
HT-MBM-160 MB/CV XXX-160 15.88 127 15.7 45.7 0.2 6.4
HT-MBM-180 MB/CV XXX-180 19.05 127 17.7 45.7 0.2 7.2
HT-MBM-200 MB/CV XXX-200 22.23 127 19.7 45.7 0.2 8.4
HT-MBM-220 MB/CV XXX-220 25.40 127 21.7 45.7 0.2 9.5

Material:
Case hardening steel, case hardened


Part Number

d1

d2 Series HK
 4X30-HK 4.0 2.4 HK040-CK55-211AK
 5X30-HK 5.0 3.0 HK050-CK55-211AK
 6X30-HK 6.0 3.0 HK060-CK55-211AK
 7X30-HK 7.0 4.1 HK070-CK55-211AK
8X30-HK 8.0 4.8 HK080-CK55-211AK
 9X30-HK 9.0 4.8 HK090-CK55-211AK
10X30-HK 10.0 6.3 HK100-CK55-211AK

Material:
Steel, Heat treated, hardness approx. HRC 50


Part Number

Expander

0
 

d1 d2

d3 - h9

l1 l2

l3

   s
LP 040 4.4 2.5 3.7 10 100 10 3.80 1.0
LP 050 5.4 3.1 4.7 10 100 15 4.76 1.3
LP 060 6.4 3.8 5.7 10 100 15 4.79 1.3
LP 070 7.4 4.6 6.7 10 100 15 4.74 1.5
LP 080 8.45 5.3 7.7 10 100 20 5.77 1.8
LP 090 9.6 6.5 8.7 14 100 20 6.23 1.8
LP 100 10.65 7.4 9.7 14 100 25 6.96 2.0
LP 120 12.75 9.1 11.7 14 100 25 7.94 2.0

Material:
Case Harderning Steel


Part Number

d1

d2 Serie SK
4X30-SK 4.0 2.7 SK 552-040
5X30-SK 5.0 3.2 SK 552-050
6X30-SK 6.0 3.7 SK 552-060
7X30-SK 7.0 4.6 SK 552-070
8X30-SK 8.0 4.8 SK 552-080
9X30-SK 9.0 5.2 SK 552-090
10X30-SK 10.0 5.6 SK 552-100

Material:
Sleeve: Stainless steel 303/304
Pin: Stainless steel 17-4PH

Part number key:

XXX is orifice diameter in hundredths of a millimeter, for example 127 for 1.27 mm, wit the decimal always in the same location.


Part Number dSeries RE  

d3

± 0.20

l1

d2

l2

x

± 0.030

s

Ref.

Data Sheet
HT-REM-040 RE-040-XXX RE-156-XXX 9.53 127 3.61 7.62 0.0 2.0  
HT-REM-050 RE-050-XXX - 9.53 127 4.78 12.70 0.0 2.7  
HT-REM-060 RE-060-XXX - 9.53 127 5.79 15.24 0.0 3.4  
HT-REM-070 RE-070-XXX RE-281-XXX 9.53 127 6.78 20.32 0.0 4.1  
HT-REM-080 RE-080-XXX RE-312-XXX 9.53 127 7.57 33.02 0.0 4.8  
HT-REM-090 RE-090-XXX - 12.70 127 8.36 38.10 0.0 5.5  
HT-REM-100 RE-100-XXX RE-406-XXX 12.70 127 9.78 38.10 0.0 6.1  
HT-REM-120 RE-120-XXX RE-468-XXX 12.70 127 11.68 38.10 0.0 7.5  
HT-REM-140 RE-140-XXX - 15.88 127 13.69 45.72 0.0 8.7  

Material:
Sleeve: Stainless steel 303/304
Mandrel: Stainless steel 17-4PH

Part number key:

XXX is orifice diameter in thousandths of an inch, for example 050 for 0.050, with the decimal always in the same location.


Part Number dSeries RE  

d3

± 0.008

l1

d2

l2

x

± 0.01

s

Ref.

Data Sheet
HT-REM-040 RE-156-XXX RE-040-XXX 0.375 5.0 0.142 0.300 0.0 0.08  
HT-REM-187 RE-187-XXX - 0.375 5.0 0.174 0.500 0.0 0.09  
HT-REM-218 RE-218-XXX - 0.375 5.0 0.205 0.600 0.0 0.11  
HT-REM-250 RE-250-XXX - 0.375 5.0 0.236 0.600 0.0 0.14  
HT-REM-070 RE-281-XXX RE-070-XXX 0.375 5.0 0.267 0.800 0.0 0.16  
HT-REM-080 RE-312-XXX RE-080-XXX 0.375 5.0 0.298 1.300 0.0 0.19  
HT-REM-343 RE-343-XXX - 0.500 5.0 0.330 1.500 0.0 0.21  
HT-REM-375 RE-375-XXX - 0.500 5.0 0.361 1.500 0.0 0.23  
HT-REM-100 RE-406-XXX RE-100-XXX 0.500 5.0 0.385 1.500 0.0 0.24  
HT-REM-437 RE-437-XXX - 0.500 5.0 0.434 1.500 0.0 0.26  
HT-REM-120 RE-468-XXX RE-120-XXX 0.500 5.0 0.460 1.500 0.0 0.30  
HT-REM-468 RE-562-XXX - 0.0625 5.0 0.549 1.800 0.0 0.35  

行业

Industries

Our parts are proven reliable in a variety of industries and applications, including transportation, fluid power, precision and microhydraulics.

worldwide

Global presence

SFC KOENIG’s efficient business networks span the globe with locations in all key regions and a broad network of Distribution Partners.

certificates

certificates

Our sealing and flow control solutions comply with global quality assurance and certification standards.